Small — px Medium — px Large — px. With the ribbons detached, you can now remove the front panel of the keyboard. The right tab will remain in the unlocked position while the left tab must be held. Locate the hinge points at the top of the netbook on each side. In order to detach the screen connector from the top left side of the motherboard you must peel back the tape holding down the fan wires. These are next to the 7mm screws you removed in the previous step. In this step, a warning sticker covers one 7 mm screw.
|Date Added:||28 August 2013|
|File Size:||70.12 Mb|
|Operating Systems:||Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X|
|Price:||Free* [*Free Regsitration Required]|
The screws are marked by red circles. For all other guides, simply removing the hard drive from the PC shown in previous steps is the only necessary step.
The side that is on the ground should not be the side that has the 7 mm screw you are trying to remove. 0100he the two pieces are loosened enough, you can place your fingers between the two pieces and lift the top piece off.
Pull sudio the edge of the piece to remove it from the connection housing. The px on the right side of the motherboard for the USB and other connections will pull free of the plastic 1000hf when the motherboard is pulled to the aaudio.
The two inner black pieces of the hinge connection, between the screen and the netbook body, are attached to the front panel that you are removing. Identify the four connection points holding the top of the keyboard to the main body of the netbook. Once the plastic piece is removed, the ribbon will spring free, but it will still be attached to the silver plate.
ASUS Eee PC HE Netbook Computer (Black) EPCHE-BLKX
The silver keyboard housing and the black piece are connected and make up the front panel. Next, remove the two 4mm screws on each side of the hard drive case shown by the blue circles. Do not continue with the next 3 steps if you are not attempting to replace your hard drive.
Small — px Medium — px Large — px. Author with 3 other contributors.
Asus Eee PC 1000HE soundcard.
Run the plastic opening tool along the side of the netbook while lifting upwards, keeping it wedged between the two asuss pieces. Run the plastic opening tool along the side of the netbook while lifting upwards, keeping it wedged between the two black pieces. In this step, a warning sticker covers one 7 mm screw. Step 5 Hard Drive. The two inner black pieces of the hinge connection, between the screen and the netbook body, are attached to the front panel that auss are removing.
Mike Glenn Member since: Locate three 7 mm screws to the right of the left hinge point in a vertical line. The right tab will remain in the unlocked position while the left tab must be held. Hold the gold 3 mm screw housing in place using the black tweezers.
Similarly, the hard drive must be disconnected from the netbook to remove the motherboard, so it must be removed prior to removing the speaker. Use the plastic opening tool or your hand to carefully lift the left hand side of the motherboard away from the bottom plastic casing.
Asus Eee PC HE Audio Driver V Driver – TechSpot
Locate one back corner of the netbook ees where the screen meets the body of the netbook. Remove the pv network card from the motherboard to detach completely.
This is due to the wire connecting the two speakers located underneath the motherboard. The speakers are visible through a cutout in the motherboard, however the motherboard still must be removed to completely access and remove asue speakers. To reassemble your device, follow these instructions in reverse order.
Locate the three 7 mm screws on the back panel, beneath where the battery would be located before removal. In order to detach the screen connector from the top left side of the motherboard you must peel back the tape holding down the fan wires. Wedge the plastic opening tool between the two asuz layers of the netbook.
Asus Eee PC 1000HE Audio Driver V22.214.171.12404
Opening up the computer screen, find the 3mm auudio screw housing to the inside of each hinge point. These are next to the 7mm screws you removed in the previous step. Proceed to the next section instead.